With the 2010-2012 GT500 Mustang Ford took this car to a level never seen before at the O.E. level. Just like the 2011+ 5.0L Mustangs, Ford put an outstanding air intake system on these cars giving the customer an extremely high level of performance and capability right from the showroom floor.
We have taken that a step further with our new ProFlow Cold Air Intake for the 2010 and Up GT500. Designed, tested, and assembled all in-house. This kit completely replaces the factory intake assembly. This kit is specifically designed to utilize the factory cold air feed from the grille and incorporates a serviceable high flow air filter, an injection molded velocity stack, black powder-coated heat shield, and our high flow ProFlow intake tube.
With a large 114mm mass air flow pipe we achieved a substantial increase in air flow at all engine rpm's, not just at redline. The heat shield seals to the hood liner and also keeps the factory cold air feed duct from taking in hot air from the engine bay for maximum power.
This GT500 cold air intake is so effective at improving airflow into the 5.4L supercharged engine that a performance tune is required for maximum performance and drivability. This intake will not work with the factory ECU calibration.
In an effort to maximize performance and provide our customers with only the very best products we have partnered with the leader in automotive tuning - SCT Performance.
Combined with the required custom tune using an SCT X4 Flash programming device we have achieved power increases of up to 36hp and 39ft/lbs of torque!
Breaking down the powerband, peak to peak gains of 32 horsepower were achieved, with point to point max gains of 36 horsepower. Peak to peak torque gains were 32ft/lbs of torque, with point to point max gains of as much as 39ft/lbs!
Power gains were achieved over the entire RPM range. More power and improved throttle response is available everywhere at any time when you need it.
If you already own a tuning device you can purchase the cold air intake by itself here, or for a complete package with the required custom tuning check out our Power Packs.
Our easy to install kit comes with premium hardware, silicone sleeves, and installation instructions.
Read more about the advantages in Steeda Mustang Cold Air Intakes over the competitors on our blog: https://www.steedablog.com/2012/03/mustang-cold-air-intake-truth/
Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.
Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.
- Does not get heat soaked like factory air box
- Cools to ambient temperature range significantly faster than the stock unit while producing more power
- Utilizes the factory cold air feed duct from the grille for low air charge temperatures
- Beautiful gloss black powder-coated heat shield
- ProFlow roto molded intake tube offers minimal heat soak maintaining cool air charge temps
- Up to 36hp and 39ft/lbs of torque on an otherwise stock car
- Steeda has been building Cold Air Intakes for Ford performance vehicles longer than any other company!
WARNING: California Residents: Cancer and Reproductive Harm; www.p65warnings.ca.gov
- Installation Difficulty:
- Tools Required:
- Basic Shop Tools
- Estimated Install Time:
- (approx.) 1 Hour
- Vehicle Fitment:
- 2010, 2011, 2012
- Vehicle Trim:
- Engine Displacement:
- Air Filter Type:
- Cold Air Intake Type:
- Open Element