Steeda's ProFlow Cold Air Intake on an otherwise stock 2011 5.0L Mustang has achieved a blistering 1/4 mile time of 11.96 at over 115mph! Steeda was the first manufacturer to get into the 11.90 range on a radial tire. Competitors had to use slicks to keep up.
Steeda Autosports, the world's largest aftermarket manufacturer of Ford performance equipment is once again leading the performance market with our High Velocity Cold Air Intake (CAI). This intake was designed before the car was even available using CAD data supplied exclusively by Ford Motor Company via our Technology Transfer program with Ford engineers.
This high performance CAI effectively opens up the intake system of Ford's new five-liter power plant and allows it to breath much more freely than the stock intake system allows - taking your 2011 & Up 5.0L Mustang to the next level of performance.
The 2011 & Up 5.0L Mustang's intake system from Ford is an excellent piece, one of the best ever to come out of Dearborn. But as usual, the engineers at Steeda were up to the challenge of making it even better for the performance customer that demands more power. Our engineers started with a large surface area high-flow nano-fiber air filter, added our famous 'race-tested' velocity stack entry and then designed a black powder-coated heat shield with a durable rubber gasket to seal the shield against the vehicle's hood. Next we increased the MAF housing size to 101mm and coupled it to a new higher flowing Pro-Flow inlet hose with our Cool-Tube Technology.
You would think this is more than enough, but we went the extra mile and designed this intake system to accept the factory sound tube should you decide you want to keep it for that robust intake sound many appreciate. Or if you want to eliminate it we provide the proper plug to delete it from the system.
To ensure the densest air charge possible we retained the factory cold air feed ducting from the front bumper. Steeda was the first company to do this starting in 2010 with our 2010 GT intake and have carried this innovation over to the 2011 model. We also sealed the black powder-coated heat shield to the hood to prevent any hot air from being sucked in from around the engine compartment. Some manufacturers have chosen to ignore the factory cold air ducting, while others don't bother to seal and isolate the airbox, which are both keys to keeping the lowest air charge temperatures possible. Also, our billet aluminum velocity stack and high flow air filter ensure a clean, streamlined air charge into the engine.
This Cold Air Intake is so effective at improving airflow into the five-liter engine that a performance tune is not just recommended, it is required for maximum performance! In an effort to maximize performance and provide our customers with only the very best products we have partnered with the leader in automotive tuning - SCT Performance.
Combined with the required custom tune using an SCT X3 Flash programming device we have achieved dramatic power increases of up to 44hp and 52ft/lbs of torque!
SCT Performance is the leader in the Ford tuning industry and Steeda's partner in developing this powerful package.
"SCT has seen the highest horsepower and torque results while using Steeda's Cold Air Kit, over any other brand." - Chris Johnson, President of SCT Performance
Our power increase it not just a peak number at one point in the band. The actual power increase is spread throughout the entire rpm range so your increased performance is available on demand in any gear at virtually any rpm!
Note: requires a minimum of 91 octane fuel for power gains.
You can purchase the intake by itself if you already own a flash programming device and intend to have your own custom tuning done or as our complete Ultimate Induction kit available separately. Check out the complete Ultimate Induction Kit which includes our Cold Air Intake matched to our SCT customer tuner, here.
Read more about the advantages in Steeda Mustang Cold Air Intakes over the competitors on our blog: https://www.steedablog.com/2012/03/mustang-cold-air-intake-truth/
Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations.
Note: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
This limited warranty is the only express warranty applicable to Steeda Autosports products. Other rights may arise or vary from state to state in the United States. Steeda is not responsible for any time for which you may lose the use of your vehicle, any inconvenience you might be caused, the loss of your transportation or any part thereof, or any other incidental or consequential damages you may have.Product Benefits
- Does not get heat soaked like factory air box
- Cools to ambient temperature range significantly faster than the stock unit while producing more power
- Easy bolt in installation
- Retains sound tube and factory cold air ducting
- Gains of up to 44 HP at peak
- Power increase at all RPM ranges - not just peak power
- Steeda has been building Cold Air Intakes for Ford performance vehicles longer than any other company!