Whipple 2010-2014 F150 5.0L 2.9L Supercharger 9 PSI Kit w/ Intercooler Black Finish

Whipple 2010-2014 F150 5.0L 2.9L Supercharger 9 PSI Kit w/ Intercooler Black Finish
439 WK-2310B
$7,395.95
$7,495.00
$99.05(1%)

Choose Options

Options
Polishing Upcharge Stage 2 (Compressor Housing, Gear Cover, Inlet, Drive, Discharge) [+$600.00]
Tune Delete [+$-200.00]
Oversize intercooler with dual fan [+$850.00]

Description

Leaving no stone unturned, Whipple's revolutionary system for the Ford 5.0L Coyote engines is truly resetting the standards of supercharging. With its massive front feed inlet, typical inlet inefficiencies are a thing of the past. With the lightweight, stainless steel tapered jack-shaft, the supercharger pulley height is offset .75" below the supercharger centerline. Why? Whipple engineers were able to add .50" thicker intercooler core and .25" more plenum volume below the core to decrease temps and pumping losses. Whipple's 2013 F150 5.0L truck, their kit produced 521 HP at the wheels on 91 octane pump gas.

Other positive displacement superchargers sacrificed plenum volume and runner size while Whipple engineer's used every square inch available to open the volume of the manifold, allowing for future expansion of power levels. Small runner and small volume manifolds cause excess boost "build-up" giving you manifold pressure, not proper cylinder pressure. This results in high boost, low power scenario's with excess heat from the lack of proper flowing air volume.
Whipple didn't just stop there, knowing that the Coyote motors love boost, Whipple’s team squeezed an epically large oversized aluminum bar and plate intercooler core into its large intake manifold, nearly 30% larger than the competition! With more open surface area, both on top of the core and the core itself, Whipple's post intercooler air temps are second to none. Cooler air equals denser air which equals more power at each boost level while being safer on engine components.

The bigger intercooler alone wasn’t enough, in previous generations, the supercharger discharge was typically too far forward from the intercooler core, and sandwiched so close to the core on top that the core’s surface area was not properly utilized. With the front feed 2.9L compressor, Whipple was able to increase the volume and distance above the intercooler core, as well as doing the same below. This issue, like some of our competition, increases the “boost” in the manifold, but not at the valves and combustion chamber. This means high boost, low power and high discharge temps. Whipple’s front feed system has a rear discharge port at nearly the center of the IC core. Through countless CFD analysis, Whipple’s design utilizes nearly the entire intercooler core, resulting in less pressure drop and cooler temps for increased power levels.

Another great feature to the Whipple Coyote kits is the oversized heat exchanger, oversized aluminum intercooler reservoir and optional dual fan kit. The oversized heat exchanger is nearly the size of the engine radiator, giving incredible cooling capacity for daily driving, drag racing or road racing. Get the dual Spal fan kit option and increase the airflow over the heat exchanger. The Whipple oversized aluminum reservoir is again a unique feature included with every kit. The aluminum reservoir is remote mounted behind the front bumper, keeping it in the cool area away from engine heat, along with having over 3 gallons of capacity in the reservoir alone! Giving the intercooler system well over 3.5 gallons of capacity. This means cooler air temps, less heat soak and more power!

The Whipple front feed system uses the stock 2013-2014 GT500 dual spray pattern, Bosch mid-length 58lb/hr fuel injectors and extruded billet high flow fuel rails to supply plenty of fuel for up to 800 engine horsepower, over 23% more capacity then the nearest competitor. Each fuel rail comes hard anodizied with laser Whipple logo engraving while the fuel injectors come with a stainless steel position lock to hold the injectors facing the optimum direction.Each Whipple system comes with proper emissions compatible fuel line with OEM quick connect fittings for simple installation.

WHIPPLE SUPERCHARGERS EXCLUSIVE FEATURES
No other upgrades required, just massive power right out of the box
Front entry W175ax (2.9 liters) Whipple twin-screw supercharger that significantly outperforms competitions 1.9L and 2.3L roots-type systems
2.9L 26% larger than 2.3L roots-type
Front feed supercharger utilizes precision ground helical cut gears vs a problematic belt
Oversized Crusher™ inlet for maximum airflow capacity and minimal rotor cavitation
Front feed allows for oversized intercooler core compared to other smaller intercooler cores giving Whipple lower air charge temps which allows more boost and timing to be run on pump gas
Massive air-to-water aluminum bar-plate intercooler offers more cooling than any other positive displacement system available, nothing comes close
Massive oversized aluminum intercooler reservoir (over 2 gallons) holds more than double any competitors IC water system allowing longer more consistent power
Whipple Superchargers massive oversized intercooled air-bypass system for industry leading reduction of burst knock and incredible fuel economy
Self-contained oversized oil system for dramatically reduced oil temps in even the most demanding conditions
Exclusive 3x5 rotor combo for significant increase in airflow under the curve than less efficient 4x6 rotor combo or 4x4 roots
Center discharge port for better cylinder to cylinder distribution then other twin-screws with cobbled together billet adapters and forward facing discharge
W175ax SC bottom is open for increased plenum volume and better over-intercooler air distribution giving more intercooler effectiveness
Extra plenum volume below intercooler core for far less pressure drop
Discharge down design allows for less pressure loss which gives more power at lower boost levels
Top mount design allows for cooler operation then upside down SC's that conduct heat from engine and are trapped by runners and covers, causing hotter manifold temps and less power per pound of boost
More boost at the "hit" than any other twin-screw
Flat torque curve for incredible acceleration
Oversized heat exchanger for incredible intercooler water temps
Fits under factory hood with no modifications
No internal modifications required
Completed installation looks factory installed, not some cobbled together kit with multiple billet adapters
Kits come complete with all necessary parts and hardware for installation
Unique oil level sight glass for easy oil level and quality check, no dipstick to bind or misread
Plug and play wiring with male and female connections
Stainless steel tapered jack-shaft with unique plastic cover (or optional carbon fiber) for increased safety
OEM quick connect fittings for easy installation, no ugly brass or steel fittings on the SC
Complete kits and Tuner kits are available
Available in wrinkle black, polish, Ford textured blue or any custom color
Easily upgradeable with big cold air intakes and bigger throttle bodies (90mm round or 140mm elliptical)
Instant boost at the touch of the throttle
3 minute pulley changes
Lightweight pocketed SC pulley

Product Benefits:

  • Up to 520 RWHP on 91 octane gas
  • No other upgrades required, comes complete with all necessary parts and hardware for installation
  • The Whipple Supercharger comes backed by a 1-Year Warranty from Whipple, Optional 3 year, 36,000 mile warranty
  • 49 state legal, not CARB compliant
  • customizable options allow expandable power / 3 minute pulley changes

Note: Please allow 6-8 weeks for delivery

MPN: WK-2310B

Fitment & Features

Installation Information
Time of Install: 6 hours
Level of Difficulty: Medium
Tools Required: Shop tools

Manufacturer
Made in USA: No

Vehicle Fitment
2010-2014 F150

Customer Reviews

There are no reviews for this product!

Related Items

More races are won...more track records are set...and more championships are captured with vehicles using Steeda performance parts than any other brand.

Steeda, the world's largest aftermarket manufacturer of Ford performance equipment, is the leader in parts and upgrades for Mustang, Fusion, Fiesta, Focus vehicles, F-150 trucks and more. With over 4,000 items, including Steeda Manufactured Suspension/Chassis components, Induction/Cold Air Intakes and Shifters, Steeda.com is your one-stop for performance parts, accessories, modifications and tuning.

Our performance parts and accessories are built by true performance enthusiasts who are dedicated to the craft they love. Steeda is the culmination of over 30 continuous years of racing history, product innovation and continuous automotive refinement driven by a passion for performance and a love for great design. At Steeda, we share a wealth of our motorsports expertise and ISO 9001:2008 Certified processes in the design, engineering, and manufacturing of our performance parts to bring a completely new level of performance and excitement to every vehicle equipped with our parts. Parts are manufactured at our Steeda Valdosta Georgia complex, home to most modern and up-to-date aftermarket facility in the world.

Speed Matters®

Steeda is an ISO 9001:2008 Certified Global Manufacturer Copyright 1988-2018 Steeda Sales & Services, LLC - All Rights Reserved Worldwide.
Unauthorized duplication or copying is strictly prohibited.
Steeda is an A+ Better Business Bureau certified Business.

Ford, Ford Mustang, Ford F-150, F-150, F150 Raptor, Raptor, Mustang GT, SVT Cobra, Cobra, Ford Lightning, Supercrew, Supercab, Power Stroke, Triton V8, Mach 1 Mustang, Shelby GT 500, GT350, GT350R, Cobra R, Bullitt Mustang, SN95, S197, S550, New Edge, V6 Mustang, Fox Body Mustang, EcoBoost, 5.0 Mustang, Ford, Ford, Ford Fusion, Ford Fusion Sport, Ford Focus, Focus, RS, S, SE, SEL, SES, ST, Duratec, Titanium, Electric, ZX3, ZX4, ZX5, ZXW, SVT, LX, ZTS, ZTW, 2.0L EcoBoost, 2.3L EcoBoost Ford Fiesta, Fiesta, S, SE, ST, Titanium, Duratec, 1.6 EcoBoost, Duratorq, Ti-VCT are registered trademarks of Ford Motor Company. Steeda Sales & Service, LLC has no affiliation with the Ford Motor Company. Throughout our website and catalog these terms are used for identification purposes only.

Top